• LightRail (3’ Extender)

     The one meter Extender Rails have a variety of uses. When added to the standard 2-meter Rail, they can be used with the Auxiliary Trolley to aid in the festooning of vent tubing, or with the Add-A-Lamp components, they can enable two grow lights to...
  • LightRail (6’ Rail)

    Normally a component in the LightRail Complete Kit, this 6' auxiliary rail can be used for extending the travel length of your LightRail setup by 6'.
  • LightRail (Slave Trolley) for 3.5

    LightRail (Slave Trolley) for 3.5

    The LightRail Auxiliary Trolley, compatible with LightRail 3.0, 3.5, 4.0 and 4.20, has many indoor growing equipment uses. So, it is the same Trolley, minus hardware, as what is packaged with the Add a Lamp Hardware. And, it’s the same Trolley that...
  • LightRail - Add A Lamp (Slave + Hardware) No Rail - Sunlight

    LightRail - Add A Lamp (Slave + Hardware) No Rail - Sunlight

    LightRail Add-A-Lamp Kit: As part of your grow equipment, this is the easiest way to move a second or third indoor garden light all from your one LightRail light mover motor. Compatible with your existing LightRail 3.0, 3.5, 4.0 or 4.20 grow light...
  • LightRail 3.5

    LightRail 3.5 IntelliDrive Kit, Light Mover Grow Light System: Our most popular light mover, LightRail 3.5 will turn your indoor grow lights into robotic lights. And, this grow light system will move an indoor grow light approximately 4 feet per...
  • LightRail 4.0 Adjustable Drive Motor w/ RailKit

    The LightRail 4.0 AdjustaDrive Kit has both a 0 to 60 second adjustable time delay for pausing the grow light at both ends of its travels, promoting even growth from end to end; but it also has a 2 to 4 feet (.6 to 1.2 meters) per minute adjustable speed...
  • LightRail 6.5 ft. Rail Only

    LightRail 6.5 ft. Rail Only

    LightRail 2-Meter (6’6”) New Rail:The 2-meter Rail is compatible with LightRail 3.0, 3.5, 4.0 and 4.20 and will handle the heaviest grow lights (75 lbs) when the Rail is first mounted continuously along the Rail to a board, with the board...
  • LightRail Add a Lamp Hardware Kit

    The Add A Lamp Hardware Kit includes a trolley and mounting hardware. It is used to hang additional crossbars or reflectors. It can also be used to festoon your power cords or cooling ducts.Light Rail 3.5 is rated to 35 lbsLight Rail 5.0 is...
  • LightRail Hanging Bracket for tents

    These Tent Hanging Brackets will enable you to hang and run a LightRail 3.0, 3.5 or 4.0 light mover in your grow tent. They are straightforward and simple to install.  
  • LightRail Robo Stick Lamp Stabilizer

    This 24″ bar is used for hanging a horizontal indoor grow light perpendicular to the direction of travel. So, this results in a wider pattern of indoor plant light coverage as your indoor grow light travels along the light mover rail.It is...
  • LightRail Switch Stop 6 pack

    Switch Stop Kit for LightRail 3.0, 3.5 and 4.0   For replacing the occasional misplaced switch stop. The SS KIT comes with 3 pairs of switch stops and that equals 6 thumb screws and 6 slide nuts. Packaged in a 4" x 4" ziplock.   Slide Nuts...